Skip to main content
Jersey City Quality Roofing
Hudson County, NJ

Commercial Flat Roof Systems in Jersey City, NJ

TPO, EPDM, PVC, and modified bitumen membrane installations engineered for Jersey City's waterfront wind, salt air, and commercial building demands.

Serving 292,449 residents in Jersey City

Get Your Free Quote

Quick response -- we'll call you back within 24 hours.

GAF Master Elite
Licensed & Insured
BBB A+ Rated
20+ Years Experience
CertainTeed SELECT

Flat Roof Systems in Jersey City: What Building Owners Need to Know

Flat roof systems on commercial buildings in Jersey City operate under conditions that would surprise building owners accustomed to inland markets. The combination of waterfront salt exposure, wind loads amplified by urban canyon effects between high-rises in Downtown, and the thermal stress of summer surface temperatures exceeding 160 degrees creates an operating environment where membrane selection, installation quality, and drainage engineering determine whether a roof system delivers its full twenty-five-year warranty life or starts failing within a decade.

We have installed and serviced flat roof systems on commercial buildings across every Jersey City neighborhood, from the modern mixed-use towers along the Exchange Place waterfront to the mid-century office buildings in Journal Square, from the industrial warehouse corridor in Bergen-Lafayette to the multi-family investment properties throughout Greenville. Each building type presents specific membrane selection criteria, drainage challenges, and equipment coordination requirements that demand a contractor with deep local experience rather than a generalist who applies the same approach to every project.

Jersey City's commercial building inventory includes approximately 2,500 structures with flat or low-slope roofs, ranging from 1,500-square-foot retail buildings to 50,000-square-foot warehouse and distribution facilities. The waterfront corridor from Liberty State Park through Exchange Place and north toward Hoboken contains the highest concentration of premium commercial buildings, where property owners expect roof systems that meet Class A standards for wind uplift, fire resistance, and energy performance. The Journal Square commercial district has a different profile: older buildings, smaller footprints, tighter budgets, and often decades of deferred maintenance that make the existing roof condition unpredictable until tear-off reveals what lies beneath the surface.

The salt air factor is something building owners who have managed properties in inland markets consistently underestimate. Galvanized steel edge metal, coping caps, and flashing components that would perform reliably for twenty years in central New Jersey show corrosion within eight to twelve years on Jersey City waterfront buildings. Metal roof accessories including HVAC curb flashing, pipe penetration collars, and parapet wall caps must be specified in aluminum, stainless steel, or factory-finished material to deliver the service life that matches the membrane warranty. We have seen building owners invest in a premium TPO membrane system only to have the galvanized edge metal fail at year ten, requiring expensive perimeter remediation that could have been avoided with proper initial specification.

Our approach to flat roof system design treats the membrane as one component of an integrated assembly that includes insulation, vapor barrier, drainage geometry, edge details, penetration flashing, and mechanical equipment support. When we design a flat roof system for a Jersey City commercial building, we engineer every component to work together under the specific conditions that building will face for the next quarter century.

Our Flat Roof Systems Process in Jersey City

1

Building Assessment & Core Sampling

0.5-1 day

Comprehensive evaluation of the existing roof system including core samples to determine layer composition, insulation condition, and deck type. Moisture survey to map wet areas.

2

System Design & Specification

3-5 days

Engineering the optimal roof system for the building including membrane selection, insulation R-value, drainage design, flashing details, and edge termination. Energy code compliance review.

3

Permit Filing & Approvals

5-15 business days

Submitting construction documents, system specifications, and wind uplift calculations to the local building department. Coordinating with building management for logistics.

4

Tear-Off & Deck Preparation

2-5 days

Removal of existing roof system (if full replacement), deck repair or replacement, and preparation of the substrate for new system installation.

5

Insulation & Tapered System Installation

2-4 days

Installing rigid insulation board to meet energy code R-values and creating positive drainage slope using tapered insulation to eliminate ponding.

6

Membrane Installation

3-7 days

Precision installation of the selected membrane system — heat-welded TPO/PVC seams, fully-adhered EPDM, or torch-applied modified bitumen — with quality control checks at every seam.

7

Flashing, Penetrations & Edge Details

1-3 days

Installation of membrane flashing at all penetrations (HVAC units, drains, vents, pipes), parapet walls, expansion joints, and perimeter edge metal.

8

Final Inspection & Warranty Issuance

1-2 days

Manufacturer representative inspection (for warranty systems), municipal final inspection, and issuance of both workmanship and manufacturer warranties.

Flat Roof Systems Across Jersey City Neighborhoods

Downtown

Downtown Jersey City's commercial flat roofs face the most demanding conditions in Hudson County. The Exchange Place corridor creates wind tunnel effects between tall buildings that amplify localized wind speeds well beyond the 115 mph code minimum. Waterfront salt spray reaches rooftops through both direct exposure and wind-carried particles that deposit on membrane surfaces and metal accessories. New mixed-use buildings in Downtown require roof systems that accommodate extensive mechanical equipment, green roof installations, and sometimes amenity deck areas for tenants, all of which create penetrations and load points that must be integrated into the membrane design without compromising waterproofing integrity.

Most Common Issue

Wind uplift on mechanically fastened membrane systems in the Exchange Place corridor where urban canyon wind acceleration exceeds standard design assumptions.

Journal Square

Journal Square's commercial flat roofs represent the largest deferred-maintenance challenge in Jersey City. Many buildings along Kennedy Boulevard and Bergen Avenue have flat roof systems that have been patched and overlaid for decades without a proper tear-off and redesign. Core sampling on Journal Square commercial buildings frequently reveals three to five layers of roofing material with trapped moisture between layers that has been degrading the insulation and sometimes the structural decking for years. For building owners in Journal Square considering a new flat roof system, the tear-off and deck restoration often represents a significant portion of the total project cost because the existing conditions are more deteriorated than surface inspection alone would suggest.

Most Common Issue

Multi-layer roof assemblies with trapped moisture causing hidden insulation and deck degradation that is not apparent from surface inspection.

Bergen-Lafayette

Bergen-Lafayette contains Jersey City's largest concentration of industrial and warehouse buildings with flat roof systems. These buildings have roof expanses ranging from five thousand to fifty thousand square feet, requiring membrane systems designed for the mechanical loads of forklift traffic on the floors below, rooftop equipment concentrated in specific areas, and the thermal movement that occurs across large uninterrupted membrane fields. The industrial building stock in Bergen-Lafayette also includes older structures with lightweight steel decking where moisture infiltration can cause corrosion that compromises structural integrity. Our flat roof installations in this area always include a deck condition assessment with special attention to steel deck connections and bearing points.

Most Common Issue

Steel deck corrosion beneath existing membrane layers on industrial buildings, discovered during tear-off and requiring structural remediation before new membrane installation.

Greenville

Greenville's commercial flat roofs are primarily on smaller retail buildings, mixed-use properties, and multi-family investment buildings. The roof footprints are typically smaller than the warehouse-scale buildings in Bergen-Lafayette, but the challenge is that many of these buildings have owners managing tight capital budgets who need a membrane system that maximizes service life relative to initial cost. We work with Greenville building owners to evaluate whether a full tear-off and premium membrane installation or a properly executed recover over the existing system provides the best value for their specific situation. Greenville's proximity to Newark Bay creates a salt air exposure similar to the waterfront, though less intense than the Exchange Place corridor.

Most Common Issue

Budget-constrained building owners choosing overlay installations that trap moisture from the existing system, accelerating deterioration of both the old and new membrane.

West Side

The West Side has a growing inventory of commercial-to-residential conversions, where former warehouse and industrial buildings have been redeveloped into loft apartments and mixed-use spaces. These conversions often inherit aging flat roof systems that were designed for industrial occupancy loads and maintenance practices but are now serving a residential use pattern where occupant comfort and zero-tolerance leak policies are the standard. Our work on West Side conversions includes upgrading flat roof systems from industrial-grade but poorly maintained membranes to modern single-ply systems with enhanced insulation and drainage that meet residential comfort expectations while handling the structural characteristics of the original commercial building.

Most Common Issue

Aging industrial-grade flat roof membranes on converted buildings that were adequate for warehouse use but fail to meet residential occupant expectations for leak-free performance.

Roofing Materials for Jersey City Flat Roof Systems

Membrane selection for commercial flat roofs in Jersey City must account for the specific performance demands of a coastal urban environment. The three primary membrane systems we install are TPO, EPDM, and modified bitumen, each with distinct advantages depending on the building type, owner priorities, and exposure conditions. TPO (thermoplastic polyolefin) in 60-mil or 80-mil thickness is our most frequently specified membrane for Jersey City commercial buildings. The white reflective surface reduces cooling costs significantly on buildings where the top floor experiences solar heat gain, which is a measurable benefit for the office buildings and mixed-use structures common in Journal Square and Downtown. TPO seams are heat-welded to create a monolithic waterproof surface that is more reliable than adhesive-bonded or tape-sealed seams, particularly in the thermal cycling conditions Jersey City experiences between summer and winter. For waterfront buildings, we specify TPO with factory-applied fleece backing that provides enhanced wind uplift resistance. EPDM (ethylene propylene diene monomer) in 60-mil thickness remains the benchmark for long-term flat roof performance. EPDM has the longest field-performance history of any single-ply membrane, and properly installed EPDM systems in the Northeast routinely exceed their twenty-five-year warranty period. The black surface absorbs more heat than TPO, which can be an advantage on buildings with significant heating loads during Jersey City's cold winters. We specify EPDM with heat-welded seams using EPDM-compatible bonding adhesive rather than the older contact-cement method, as the heat-welded approach provides superior seam integrity under thermal cycling stress. Modified bitumen in a two-ply torch-applied system provides the highest puncture resistance and is preferred for buildings with significant rooftop traffic from maintenance personnel accessing mechanical equipment. The multi-layer configuration provides redundancy that single-ply systems lack: if the cap sheet is punctured, the base sheet continues to prevent water intrusion until the breach is repaired. For the industrial and warehouse buildings in Bergen-Lafayette where rooftop access is frequent and equipment loads are concentrated, modified bitumen is often the most practical choice. Regardless of membrane type, all flashing components, edge metal, and mechanical curb attachments on Jersey City commercial buildings should be specified in aluminum or stainless steel. Galvanized steel corrodes too quickly in the salt air environment to justify the initial cost savings.

TPO (Thermoplastic Polyolefin)

A single-ply reflective membrane heat-welded at seams, offering excellent energy efficiency and chemical resistance.

20-30 years$5.50-$9.00 per sq ft installed

EPDM (Ethylene Propylene Diene Monomer)

A synthetic rubber membrane available in large sheets, ideal for covering large flat roof areas with minimal seams.

25-30 years$4.50-$8.00 per sq ft installed

PVC (Polyvinyl Chloride)

A premium single-ply membrane with heat-welded seams, offering the highest chemical and fire resistance among flat roof options.

25-35 years$6.50-$11.00 per sq ft installed

Modified Bitumen

Multi-layer asphalt-based membrane system applied by torch, hot mop, or cold adhesive, providing redundant waterproofing layers.

15-25 years$4.00-$7.50 per sq ft installed

Common Flat Roof Systems Challenges in Jersey City

The installation process for a commercial flat roof system in Jersey City follows a sequence designed for the urban logistics, permitting requirements, and building occupancy considerations specific to this market. Project engineering begins with a comprehensive building assessment including core sampling, drainage mapping, structural analysis of the existing deck, and a catalog of all rooftop penetrations and mechanical equipment. We produce an engineered design package that includes the membrane layout, insulation taper plan, drainage calculations, wind uplift resistance verification, and edge detail specifications. For buildings in the Exchange Place corridor where wind loads exceed standard assumptions, we engage a structural engineer to verify that the deck and attachment system can handle the design loads. Permitting for commercial roof work in Jersey City requires a building permit through the Division of Construction plus any applicable fire department review for buildings with hot-work membrane installation such as torch-applied modified bitumen. The permit review for commercial projects typically takes seven to fifteen business days. We submit applications immediately after the owner approves the project scope and begin material procurement during the review period to minimize idle time. Material procurement for commercial projects is coordinated directly with membrane manufacturers to ensure quality control, warranty eligibility, and delivery scheduling. We stage materials in phased deliveries to avoid overloading the roof structure and to maintain emergency building access throughout the project. For Downtown buildings with limited street-level staging area, we arrange crane hoisting on scheduled days with city street-use permits. Installation follows the manufacturer-specified sequence, with each phase inspected by our project superintendent before the next phase begins. Tear-off and deck preparation come first, followed by vapor barrier installation, insulation placement, membrane application, and finally flashing and edge metal installation. We maintain a watertight condition at the end of each work day, meaning any exposed areas are temporarily sealed to protect the building interior overnight and over weekends. This is particularly critical for occupied commercial buildings where interior water damage would disrupt business operations. Final inspection includes our own quality verification, the municipal building inspection, and the manufacturer's representative inspection required for warranty activation. We provide the building owner with a complete project file including the engineer's design, as-built documentation, material certifications, warranty certificates, and a maintenance schedule specific to the installed system and Jersey City's environmental conditions.

  • Waterfront salt air corrosion on metal flashing and fasteners
  • Historic district permit requirements for landmarked brownstones
  • Waterfront wind exposure accelerates shingle wear
  • Ponding water due to insufficient drainage slope — a common issue in Jersey City due to the area's moderate hurricane risk and 2-3 per year nor'easters
  • Historic district overlay permits for Paulus Hook, Van Vorst Park, and Hamilton Park

Need Flat Roof Systems in Jersey City?

Free estimates with no obligation.

Commercial flat roof system costs in Jersey City range from eight to eighteen dollars per square foot installed, depending on the membrane type, existing conditions, insulation requirements, and project complexity. For a typical commercial building, total project costs range from forty thousand dollars for a smaller retail structure to over two hundred thousand dollars for a large warehouse or multi-story office building. The primary cost factors specific to Jersey City commercial flat roof installations include the scope of tear-off and deck preparation, which is often more extensive than initial assessment suggests due to hidden moisture damage and multi-layer conditions common on older buildings. Insulation costs are driven by both the required R-value for energy code compliance and the tapered insulation design needed to create positive drainage. Mechanical equipment coordination adds cost when HVAC units must be temporarily supported or relocated during membrane installation. Crane and material hoisting costs for multi-story buildings in Downtown and Journal Square can represent five to ten percent of the total project budget. For building owners evaluating competing proposals, we recommend comparing specifications rather than bottom-line prices. A sixty-mil fully adhered TPO system with heat-welded seams, tapered insulation, and stainless steel edge metal will cost more than a forty-five-mil mechanically fastened system with flat insulation and galvanized edge metal, but the former will deliver twenty-five years of reliable service while the latter may begin showing problems within ten years in Jersey City's demanding environment. The per-year cost of a premium system is almost always lower than the per-year cost of a budget installation when maintenance and premature replacement are factored in.

What Affects Your Flat Roof Systems Cost

Roof Area

Commercial roofs are measured in squares (100 sq ft). A 10,000 sq ft warehouse roof is 100 squares — material and labor scale linearly with area.

high

Membrane System Selection

TPO and EPDM are cost-effective. PVC is premium. Modified bitumen falls in between. The choice depends on building use, energy goals, and maintenance budget.

high

Existing Roof Condition

A recover (new membrane over existing) costs 30-40% less than a full tear-off and replacement. Core sample analysis determines if recover is viable.

high

Insulation Requirements

NJ energy code requires minimum R-30 for commercial roofs. Adding tapered insulation for drainage increases both material and labor costs.

moderate

Rooftop Equipment

HVAC units, exhaust fans, satellite dishes, and other penetrations require individual flashing details that add to the scope and cost.

moderate

Access and Logistics

Urban commercial buildings with limited parking and staging area require crane lifts for material delivery, increasing mobilization costs.

moderate

A Real Flat Roof Systems Story in Jersey City

We recently completed a flat roof system replacement on a 12,000-square-foot mixed-use building in Journal Square. The building houses ground-floor retail with three floors of office space above. The existing roof was a modified bitumen system installed approximately eighteen years prior, with multiple patches from intervening repairs visible across the surface.

Our pre-installation assessment included core sampling at eight locations across the roof. The results revealed that the existing modified bitumen cap sheet was intact in most areas, but the base sheet beneath it had debonded from the polyisocyanurate insulation across approximately forty percent of the roof area. More concerning, the insulation moisture content exceeded fifteen percent in three of the eight core locations, concentrated around the mechanical equipment area where HVAC curb flashing had failed and allowed water to migrate beneath the membrane for years. The moisture had degraded the insulation R-value in those areas to less than half the original specification.

We recommended a full tear-off rather than a recover. The building owner initially preferred a recover to reduce cost, but we demonstrated through the core sample data that installing a new membrane over wet insulation would trap the moisture permanently and lead to premature system failure from below. The owner agreed to the tear-off approach.

The project scope included removing all existing membrane and insulation, inspecting and repairing the steel deck substrate, installing a new vapor barrier, applying two layers of tapered polyisocyanurate insulation to create positive drainage toward the existing interior drains, installing a 60-mil TPO membrane with heat-welded seams, replacing all HVAC curb flashing with prefabricated curb assemblies, and installing new stainless steel edge metal along the full perimeter. We selected TPO over EPDM for this project because the white reflective surface reduces cooling costs on a building where the top-floor offices were experiencing significant solar heat gain through the existing dark-colored modified bitumen system.

The installation took eight working days. We staged material deliveries across three mornings to avoid overloading the deck and to maintain unobstructed emergency access for the building. The total project cost was approximately one hundred fifteen thousand dollars, which included the deck repairs, full insulation replacement, and upgraded mechanical equipment flashing. The building owner received a twenty-five-year manufacturer warranty covering both material and labor, contingent on our annual maintenance inspections for the first three years.

What Our Customers Say

After the nor'easter damaged our 1920s brownstone roof on Van Vorst Street, Jersey City Quality Roofing replaced the entire thing in four days. They handled the historic district permit and matched the slate look with architectural shingles. Outstanding crew — clean, professional, and on schedule every day.

Michael Rodriguez

Jersey City

We had a persistent leak in our Heights apartment building that three other contractors could not find. Jersey City Quality Roofing used an infrared camera and traced it to a failed pipe boot two floors away from the ceiling stain. Fixed in one afternoon. Should have called them first.

Sarah Kim

Jersey City

We hired them for a full TPO roof system on our Journal Square commercial building — about 8,000 square feet. The crew worked efficiently around our tenants, the tapered insulation eliminated the ponding problem we had for years, and the manufacturer warranty gives us peace of mind for decades.

David Okonkwo

Jersey City

A tree branch came through our roof during a summer storm in Bergen-Lafayette. They had a crew here within the hour tarping the hole and boarding it up. The permanent repair was done the following week. Only wish they had weekend scheduling for the follow-up, but the emergency response was top-notch.

Angela Martinez

Jersey City

Our Bloomfield Street brownstone had ice dam damage along the entire front eave last winter. These guys repaired the flashing, replaced the damaged shingles, and recommended ventilation improvements to prevent recurrence. Very knowledgeable about Hoboken's older buildings.

James O'Brien

Hoboken

Replacing the roof on our Washington Street row house required Historic District Commission approval. Jersey City Quality Roofing handled the entire application process and used materials that satisfied the commission while actually improving the roof performance. Five stars for navigating Hoboken's red tape.

Priya Patel

Hoboken

We were buying a third-floor condo on Park Avenue and needed a roof inspection of the building. Their report was incredibly detailed — infrared photos, moisture readings, estimated remaining life, and a maintenance plan. The seller ended up crediting us $8,000 toward the purchase based on the findings.

Thomas Walsh

Hoboken

During last March's nor'easter, our flat roof membrane blew open on Garden Street and water was pouring into our top-floor apartment. They came out at 11 PM, tarped everything, and had us dry by morning. Emergency response in Hoboken doesn't get better than this.

Maria Gonzalez

Hoboken

Our Cape Cod on Avenue C needed a complete roof replacement — the old 3-tabs were curling and missing after 25 years. They installed GAF Timberline HDZ shingles with ice-and-water shield along all the eaves and valleys. Beautiful result, and the dormers look great.

Robert Kowalski

Bayonne

Had a leak around the chimney flashing on our two-family on East 22nd Street. They replaced all the step and counter flashing and re-sealed the cricket. No more leaks through two heavy rainstorms since. Price was fair for the amount of work involved.

Josephine DeLuca

Bayonne

We had them inspect our Bergen Point rental property after a tenant complained about a ceiling stain. Turned out it was a condensation issue from inadequate attic ventilation, not a roof leak. They explained the difference clearly and recommended a fix. Saved us from an unnecessary roof repair.

Carlos Ramirez

Bayonne

Wind ripped the ridge cap off our house near Stephen Gregg Park during a storm. Water was running down both sides of the ridge into the attic. They were here in under an hour, sealed everything up that night, and did a full ridge cap replacement two days later.

Patricia Murphy

Bayonne

Our split-level on Woodcliff Avenue sits right on the Palisades ridge where the wind is brutal. They installed a wind-rated system with six nails per shingle instead of the standard four, plus extra ice shield in the valleys. First winter with zero issues after years of wind damage with the old roof.

Ahmed Hassan

North Bergen

We own a retail building on Tonnelle Avenue and needed the flat roof replaced. The modified bitumen was failing everywhere. They installed a new TPO system with proper drainage and it completely solved the ponding water problem. Great job on a large commercial project.

Lisa Chen

North Bergen

The valley on our colonial in Tyler Park was leaking into the dining room. They replaced the valley flashing and underlayment and re-shingled the affected area. Good work, though scheduling took a bit longer than expected due to their busy season.

Anthony Ferraro

North Bergen

We signed up for their commercial maintenance program for our garden apartment complex near Braddock Park. Twice a year they inspect, clean the drains, and fix small issues before they become big ones. Our emergency repair costs have dropped to nearly zero since we started.

Fatima Begum

North Bergen

Our row house on Bergenline has a flat roof that shares walls with both neighbors. These guys understood the shared-wall flashing situation perfectly — they repaired our side without disturbing the neighbor's roof. Hard to find contractors who understand Union City row house roofing.

Juan Herrera

Union City

Replacing the flat roof on our three-family walk-up in Union Hill was a challenge because of the tight street access. They managed the material delivery with a crane from the alley side and finished in three days. EPDM membrane with proper drainage — no more ponding.

Veronica Santos

Union City

They repaired the flat roof over our restaurant on Bergenline Avenue. The PVC membrane had separated at a seam near the kitchen exhaust vent. They heat-welded a patch and re-detailed the vent flashing. Solid work. Building manager was happy with the minimal disruption.

Ricardo Morales

Union City

We were considering buying a multi-family property on New York Avenue and needed a roof assessment. Their inspection revealed the flat roof had less than two years of life left — something the seller's disclosure didn't mention. That report saved us $20,000 in negotiation.

Catherine Reilly

Union City

Our apartment building on Boulevard East takes a beating from the Palisades wind. They installed a fully-adhered TPO system with extra fastening at the perimeter edges. Two winters now with zero issues. The crew knew exactly how to handle the wind exposure up here.

Diego Vargas

West New York

The parapet wall on our walk-up near Park Avenue was letting water behind the membrane. They rebuilt the parapet cap, installed new through-wall flashing, and re-terminated the membrane. Problem solved after years of patching by other contractors.

Sofia Petrov

West New York

During a December ice storm, the membrane on our flat roof split open and water poured into the top-floor apartment. They responded within two hours and got us sealed up before the next wave of freezing rain. Fast emergency work on a difficult night.

Omar Fayed

West New York

We manage several apartment buildings in West New York and enrolled them all in the maintenance program. The semi-annual inspections catch problems before our tenants notice anything. Drain cleaning alone has prevented multiple potential emergency calls.

Elena Romero

West New York

Our Harmon Cove townhouse roof was 30 years old and growing moss from all the Meadowlands humidity. They replaced it with algae-resistant architectural shingles and improved the ventilation. The HOA approved the color match and the installation was immaculate.

Kevin Brennan

Secaucus

They replaced the entire roof on our 25,000 sq ft warehouse near the Turnpike. Managed the project in phases so we never had to shut down operations. The new TPO system came with a 20-year manufacturer NDL warranty. Professional operation from start to finish.

Linda Tran

Secaucus

Had them inspect the roof on a Clarendon single-family home we were buying. Their report identified that the previous owner had layered new shingles over old ones — technically over code limit. We used that to negotiate the price down significantly.

Brian Sullivan

Secaucus

Our Millridge home had algae streaking all over the north-facing slope — a common problem near the Meadowlands. They cleaned the roof, replaced a few damaged shingles, and applied a zinc strip to prevent regrowth. Looks like a new roof.

Grace Park

Secaucus

Replaced the roof on our colonial near Gunnell Oval. The old roof was the original from when the house was built in the 1960s — way overdue. They did a clean tear-off, replaced about 15% of the decking, and installed a beautiful charcoal architectural shingle. Huge improvement.

Sean McCarthy

Kearny

Our industrial building in South Kearny near the marsh had a failing BUR roof. They installed a new EPDM system designed for the high-humidity environment with enhanced seam adhesion. No more leaks into the warehouse. The crew handled the large-scale project expertly.

Jennifer Andrade

Kearny

Ice dams damaged the eaves on our Cape Cod on Elm Street. They repaired the damaged fascia, replaced the affected shingles, and installed additional ice-and-water shield to prevent recurrence. Good work, though I wish ice dam prevention was included in the original assessment.

William Taylor

Kearny

Before listing our Passaic Avenue two-family for sale, we had them do a full roof inspection. Their report showed the roof was in good condition with 8-10 years remaining — which we included in the listing. Helped sell the property faster at asking price.

Rosa Gutierrez

Kearny

Our two-family on Harrison Avenue needed a new roof before we could refinance. They completed the replacement in three days — tear-off, decking repairs, new architectural shingles, and all new flashing. The bank appraiser was impressed with the quality.

Daniel Park

Harrison

We manage a new luxury building in the Waterfront District and had a warranty issue with the original roof contractor. Jersey City Quality Roofing came in, identified the membrane defects, documented everything for our warranty claim, and did the repair correctly.

Christine Alvarez

Harrison

Leak around the kitchen vent pipe on our older home near West Hudson Park. They replaced the pipe boot and the surrounding shingles. Quick, clean, and no more water stain spreading across the ceiling. Simple job done right.

Frank DiNapoli

Harrison

We needed a roof condition assessment for our building's reserve study near the PATH station. Their detailed report with photos and estimated replacement timeline gave our condo board exactly what we needed for long-term capital planning.

Yuki Tanaka

Harrison

Our two-family on Grant Avenue had the original roof from 1948. They navigated the tight streets with their equipment, did a careful tear-off given the shared walls with our neighbors, and installed a new roof that completely transformed the look of the house.

George Papadopoulos

East Newark

The shared-wall flashing between our row house and the neighbor's was leaking into both units. They coordinated with both homeowners, replaced the party wall flashing, and sealed everything properly. The kind of job that requires real row house experience.

Diane Wilson

East Newark

Had them inspect our small multi-family on Third Street before a planned renovation. Their report identified soft spots in the decking that we never would have found without pulling up the shingles. Changed our renovation budget significantly, but better to know now.

Joseph Medina

East Newark

A piece of the neighbor's aluminum siding flew off during a storm and punctured our flat roof membrane. Water was coming through the kitchen ceiling. They were here in 45 minutes and had the hole sealed before any serious damage to the interior.

Helen Stavros

East Newark

Our mid-rise apartment building on Park Avenue needed a complete flat roof replacement. The density in Guttenberg makes logistics a nightmare, but they managed material deliveries by crane and completed the TPO installation on schedule. Impressive project management.

Victor Petrosyan

Guttenberg

We're on the condo board for a Boulevard East building. Their maintenance program has been invaluable — the semi-annual inspections catch wind damage early before it turns into interior leaks. The annual reports help us budget for future capital improvements.

Margaret Kim

Guttenberg

Our mixed-use building had a persistent leak above the commercial space on the ground floor. They traced it to a deteriorated drain connection on the flat roof and replaced the entire drain assembly. Leak resolved. Getting equipment up to the roof in Guttenberg is always a challenge but they handled it.

Ivan Sokolov

Guttenberg

We needed a comprehensive roof assessment for all three buildings in our Galaxy Towers-adjacent complex. Their team inspected every section, mapped the moisture conditions, and gave us a prioritized 5-year replacement plan. The board voted to approve the maintenance contract on the spot.

Donna Cassidy

Guttenberg

Replacing the roof on our Victorian in the Heights was tricky — steep pitch, limited access from the narrow lot, and the wind exposure from being near the cliff edge. They handled every challenge and the new architectural shingles look amazing against the original trim.

Patrick Doyle

Weehawken

We needed emergency repair on a Lincoln Harbor commercial building where the membrane had blown up at the parapet during a windstorm. They were there the same day, secured the membrane, and scheduled the permanent repair for the following week. Responsive and competent.

Natasha Volkov

Weehawken

Our King Avenue townhouse had a leak at the skylight curb. They re-flashed the entire skylight and sealed the curb. It took longer than quoted because they found the decking around the skylight was soft, but they fixed it all and the leak is gone.

Mark Santangelo

Weehawken

Before purchasing our waterfront condo at Port Imperial, we wanted an independent assessment of the building's roof system. Their report confirmed the roof was in excellent condition with 15+ years remaining. It was exactly the peace of mind we needed for that investment.

Aisha Mohammed

Weehawken

Frequently Asked Questions About Flat Roof Systems in Jersey City

Jersey City Division of Construction requires permits for most roofing work. Yes, a permit is required for flat roof systems projects in Jersey City. The municipality follows 2021 IRC/IBC as adopted by NJ DCA with wind speed requirements of 115 mph per ASCE 7-22. Additional requirements include: historic district overlay permits for paulus hook, van vorst park, and hamilton park.

Request a Detailed Quote

Tell us about your project and we'll prepare a comprehensive estimate.

Your Trusted Jersey City Flat Roof Systems Experts

Call now for a free commercial roof assessment or request your no-obligation quote.