Skip to main content
Jersey City Quality Roofing
Hudson County, NJ

Flat Roof Systems in Union City, NJ

Engineered flat roof solutions for Union City's thousands of row houses and multi-family buildings, where virtually every rooftop is flat and the extreme density demands membrane systems built for shared-wall construction.

Serving 73,999 residents in Union City

Get Your Free Quote

Quick response -- we'll call you back within 24 hours.

GAF Master Elite
Licensed & Insured
BBB A+ Rated
20+ Years Experience
CertainTeed SELECT

Flat Roof Systems in Union City: What Building Owners Need to Know

If there is one municipality in New Jersey that defines the flat roof, it is Union City. With approximately 25,000 housing units packed into 1.27 square miles, virtually every residential and commercial building in this city has a flat or low-slope roof. The three-story row houses that form the backbone of Union Hill, the mixed-use buildings lining Bergenline Avenue, the walk-up apartment buildings throughout the Heights, and the commercial properties in the Transfer Station area all rely on flat membrane systems to keep the weather out. Understanding flat roof systems in Union City is not a specialty for us; it is the core of our practice in this city, because there are essentially no pitched roofs to divert our attention.

The flat roof landscape in Union City is dominated by three membrane types: modified bitumen, EPDM rubber, and TPO single-ply. Each has a history in this city and a track record that the extreme density modifies compared to manufacturer specifications. Modified bitumen was the standard installation on Union City row houses from the 1970s through the 2000s, and the torch-applied two-ply systems of that era still cover thousands of buildings across Union Hill and the surrounding blocks. EPDM became popular in the 1990s and 2000s for its lower installation cost and easier application on the tight row house rooftops where open-flame torch work creates fire risk in the dense construction environment. TPO has emerged as the preferred system for new installations and replacements over the past decade, offering the reflective surface that helps manage the heat buildup between shared-wall row houses and the chemical weld seaming that creates stronger joints than adhesive-bonded EPDM.

What makes flat roof system selection and installation fundamentally different in Union City is the shared party wall construction. Every row house flat roof terminates at masonry parapets on two or more sides, and the connection detail between the membrane and the parapet is the most failure-prone junction on any Union City roof. The membrane must be secured to the masonry with a termination bar and counterflashing system that accommodates the differential movement between the roof membrane, which expands and contracts with temperature changes, and the masonry parapet, which moves at a different rate and in different directions. When this detail is executed incorrectly, the membrane pulls away from the wall, water enters the parapet cavity, and leaks develop that appear inside the building far from the actual failure point. We have rebuilt this detail on hundreds of Union City parapets, and the two-piece independent flashing system we install allows each property owner to maintain their side of the shared wall without affecting the neighbor's membrane termination.

The heat island effect between Union City's tightly packed buildings dramatically affects flat roof performance. On a freestanding building, the roof membrane is exposed to direct sunlight and ambient air temperature. On a Union City row house, the roof membrane is exposed to direct sunlight plus radiated heat from the adjacent building's walls, plus the trapped heat in the narrow airspace between buildings that cannot dissipate efficiently. We have measured rooftop surface temperatures on Union Hill row houses that are fifteen to twenty degrees higher than the ambient air temperature during summer, a differential that accelerates membrane aging, reduces the effectiveness of adhesive bonds, and shortens the service life of any system by years compared to the manufacturer's stated lifespan for open-air installations.

The drainage challenge on Union City flat roofs is compounded by the age and settling of the building stock. A flat roof that was properly sloped toward its drains when the building was constructed in 1930 may no longer drain effectively after ninety years of building settlement and structural movement. Ponding water, which we define as water remaining on the surface more than 48 hours after a rain event, accelerates membrane deterioration, adds structural load to the framing, and creates leak risk at every seam and penetration within the ponding zone. When we install or replace a flat roof system in Union City, we use tapered insulation boards to re-establish positive drainage slope regardless of the current deck condition, ensuring that the new system sheds water effectively even if the underlying structure has shifted over the decades.

The commercial flat roofs along Bergenline Avenue and in the Transfer Station area operate under different performance requirements than the residential row house roofs. These rooftops support HVAC equipment, exhaust fans, satellite dishes, and regular foot traffic from maintenance workers. The membrane system must resist puncture from dropped tools, compression from equipment stands, and abrasion from foot traffic paths. We specify reinforced eighty-mil TPO for commercial flat roof installations in Union City, with walkway pads at all traffic paths and equipment curbs raised to a minimum of eight inches to keep the membrane visible and accessible for inspection around each penetration.

Our Flat Roof Systems Process in Union City

1

Building Assessment & Core Sampling

0.5-1 day

Comprehensive evaluation of the existing roof system including core samples to determine layer composition, insulation condition, and deck type. Moisture survey to map wet areas.

2

System Design & Specification

3-5 days

Engineering the optimal roof system for the building including membrane selection, insulation R-value, drainage design, flashing details, and edge termination. Energy code compliance review.

3

Permit Filing & Approvals

5-15 business days

Submitting construction documents, system specifications, and wind uplift calculations to the local building department. Coordinating with building management for logistics.

4

Tear-Off & Deck Preparation

2-5 days

Removal of existing roof system (if full replacement), deck repair or replacement, and preparation of the substrate for new system installation.

5

Insulation & Tapered System Installation

2-4 days

Installing rigid insulation board to meet energy code R-values and creating positive drainage slope using tapered insulation to eliminate ponding.

6

Membrane Installation

3-7 days

Precision installation of the selected membrane system — heat-welded TPO/PVC seams, fully-adhered EPDM, or torch-applied modified bitumen — with quality control checks at every seam.

7

Flashing, Penetrations & Edge Details

1-3 days

Installation of membrane flashing at all penetrations (HVAC units, drains, vents, pipes), parapet walls, expansion joints, and perimeter edge metal.

8

Final Inspection & Warranty Issuance

1-2 days

Manufacturer representative inspection (for warranty systems), municipal final inspection, and issuance of both workmanship and manufacturer warranties.

Flat Roof Systems Across Union City Neighborhoods

Union Hill

Union Hill contains the densest concentration of residential flat roofs in Union City, with three-story row houses packed block after block between Bergenline Avenue and New York Avenue. The flat roofs here are predominantly modified bitumen and EPDM from installations spanning the 1970s through the 2000s, with many buildings carrying two or three overlays on the original deck. The heat trapped between the shared-wall row houses in Union Hill drives rooftop temperatures to extremes that shorten membrane life by five to ten years compared to freestanding installations. New flat roof systems in Union Hill should prioritize reflective TPO to combat the heat island effect and fully adhered installation to maximize the membrane-to-deck bond in this thermal-stress environment.

Most Common Issue

Accelerated membrane aging from the heat island effect between tightly packed shared-wall row houses, shortening flat roof service life well below manufacturer projections.

Bergenline Avenue Corridor

Bergenline Avenue flat roofs serve commercial and mixed-use buildings where the rooftop functions as an equipment platform as much as a weather barrier. The flat membrane must handle the concentrated loads from HVAC condensing units, exhaust fan curbs, and the foot traffic of maintenance workers accessing this equipment monthly or more frequently. Standard residential-grade sixty-mil membrane cannot withstand this use pattern; we install eighty-mil reinforced TPO with dedicated walkway pads, equipment pads, and raised curbs that keep the membrane accessible for inspection. The Bergenline corridor also presents unique drainage challenges because the buildings span the commercial depth of the block, creating large flat surfaces where ponding accumulates if the original drainage slope has been lost to decades of settling.

Most Common Issue

Membrane puncture and compression damage from commercial rooftop equipment loads and maintenance foot traffic on undersized residential-grade flat roof systems.

West Hoboken

While West Hoboken is known for its Victorian steep-pitched roofs, the flat roof sections on row houses and lower building additions in this neighborhood require the same attention as any other flat roof in Union City. Many West Hoboken properties have hybrid systems where a flat membrane section sits adjacent to a steep-pitched slate or shingle section, and the flat portion often serves as a walkable terrace or equipment platform for the larger building. The flat sections in West Hoboken tend to be smaller in footprint than Union Hill row house roofs, but the transition detail where flat meets pitched is the critical engineering challenge. A flat roof system in West Hoboken must integrate seamlessly with the adjacent pitched surface through a counter-flashing detail that accommodates the different movement rates of the two roof types.

Most Common Issue

Failed transition details where flat membrane sections meet adjacent steep-pitched roof surfaces on hybrid buildings typical of the West Hoboken building mix.

Heights / Palisade Avenue

The Heights section flat roofs face Palisades cliff-edge wind conditions that demand fully adhered membrane installations. Mechanically fastened flat roof systems in this neighborhood have a documented history of flutter, fastener pullout, and premature membrane fatigue from the sustained wind cycling that buildings at this elevation endure. We do not offer mechanically fastened installations in the Heights section because the wind data does not support them for long-term service life. Fully adhered TPO with structural adhesive rated for wind uplift pressures exceeding the ASCE 7-22 specification is our standard for every Heights flat roof, whether residential or the mid-century apartment buildings that characterize this elevated portion of the city.

Most Common Issue

Wind-induced membrane flutter and fastener pullout on mechanically fastened flat roof systems at Palisades elevation where sustained winds exceed standard design parameters.

Transfer Station Area

Transfer Station area flat roofs on commercial and industrial buildings are the largest in Union City by square footage, sometimes exceeding five thousand square feet on a single plane. These large flat surfaces require careful drainage design with multiple drain locations and tapered insulation systems that create positive slope across the full roof area. The proximity to Route 495 creates ground vibration from heavy truck traffic that affects mechanically fastened systems, making fully adhered or ballasted installations preferable for long-term performance. The commercial tenants in this area often modify their rooftop equipment configuration as businesses change, which means the flat roof system must accommodate new penetrations and equipment locations throughout its service life without compromising the membrane integrity.

Most Common Issue

Drainage design failures on large commercial flat roof surfaces where building settlement and inadequate slope create persistent ponding across extended roof areas.

Roofing Materials for Union City Flat Roof Systems

Flat roof material selection in Union City must account for the thermal extremes, shared-wall construction, drainage challenges, and access constraints that distinguish this city from any other installation environment. The material that performs well on a suburban flat roof may underperform significantly on a Union City row house where the operating conditions are harsher than the manufacturer ever tested for. TPO single-ply membrane in sixty-mil thickness is our standard specification for Union City residential flat roofs. The white reflective surface reduces heat absorption by forty to fifty percent compared to dark modified bitumen or black EPDM, which is critical in Union City where the heat island effect between shared-wall row houses drives rooftop temperatures fifteen to twenty degrees above ambient. The chemical weld seaming process that TPO uses creates a homogeneous bond at every overlap that is stronger than the field membrane itself, eliminating the adhesive-bonded seam failures that plague EPDM in the high-thermal-stress Union City environment. Fully adhered installation is our standard for Union City TPO because the uniform bond to the insulation layer eliminates the air voids that mechanically fastened systems create, which are vulnerable to both wind uplift and the thermal pumping effect that the Union City heat island amplifies. For commercial flat roofs on Bergenline Avenue and in the Transfer Station area, we upgrade to eighty-mil reinforced TPO. The reinforced scrim provides puncture resistance rated for maintenance foot traffic and the concentrated loads from HVAC equipment stands. Commercial flat roofs also receive walkway pads at all designated traffic paths and equipment pads beneath heavy units, protecting the membrane from the repeated compression and abrasion that commercial use demands. Insulation beneath the flat roof membrane uses polyisocyanurate board exclusively. Polyiso maintains its R-value even when exposed to incidental moisture, which is critical in Union City where the shared-wall construction can introduce moisture at the membrane-to-parapet junction. We avoid expanded polystyrene on Union City flat roofs because EPS absorbs water and loses insulating value when wet, creating a cycle of diminishing thermal performance that accelerates in the dense urban microclimate. Tapered polyiso sections create positive slope toward drain locations, ensuring that the flat roof sheds water effectively regardless of any settlement the building has experienced since original construction.

TPO (Thermoplastic Polyolefin)

A single-ply reflective membrane heat-welded at seams, offering excellent energy efficiency and chemical resistance.

20-30 years$5.50-$9.00 per sq ft installed

EPDM (Ethylene Propylene Diene Monomer)

A synthetic rubber membrane available in large sheets, ideal for covering large flat roof areas with minimal seams.

25-30 years$4.50-$8.00 per sq ft installed

PVC (Polyvinyl Chloride)

A premium single-ply membrane with heat-welded seams, offering the highest chemical and fire resistance among flat roof options.

25-35 years$6.50-$11.00 per sq ft installed

Modified Bitumen

Multi-layer asphalt-based membrane system applied by torch, hot mop, or cold adhesive, providing redundant waterproofing layers.

15-25 years$4.00-$7.50 per sq ft installed

Common Flat Roof Systems Challenges in Union City

The flat roof system installation process in Union City begins with a pre-construction assessment that evaluates both the roof conditions and the logistical constraints specific to the building's location. We document the existing membrane type and layer count, the deck substrate condition, the parapet wall integrity on all shared boundaries, the drainage configuration and any slope deficiencies, and the access routes for material delivery and debris removal. Material selection is confirmed based on the pre-construction findings. We present the property owner with a detailed scope document that specifies the membrane type, insulation configuration, parapet flashing design, and drainage improvements included in the project. For multi-building portfolio projects, we present a phased plan that sequences the work across adjacent buildings to maximize cost efficiency and minimize disruption to tenants. Permitting through the City of Union City Construction Department includes the scope of work, material specifications, and code compliance documentation. For pre-1978 buildings, asbestos testing of existing roofing materials is completed and submitted with the permit application. DPW parking permits for material delivery vehicles and dumpster placement are secured in advance to ensure the logistics are in place before the crew arrives. Installation follows a controlled sequence: full tear-off of existing layers to the deck on day one with temporary waterproofing applied at the end of day, deck inspection and structural repair on day two morning, insulation installation with tapered slope sections in the afternoon of day two, membrane installation on day three with seam welding and perimeter termination, and flashing, drain, and penetration detail work on day four. The shared parapet flashing system is installed after the membrane is in place, with coordination for adjacent property owners scheduled to align with the work window. Post-installation inspection by the Union City Construction Department is scheduled within one week. We perform our own quality verification before the city inspection, including flood testing of all drains and infrared scanning of the completed membrane to verify full adhesion across the entire surface. The property owner receives a warranty package that includes both the manufacturer's material warranty and our workmanship warranty, along with a maintenance schedule tailored to the specific flat roof system installed and the Union City conditions it will face.

  • Densest municipality in NJ makes equipment access extremely difficult
  • Shared-wall row house construction complicates individual roof repairs
  • Dense row house construction trapping heat and moisture between shared walls
  • Ponding water due to insufficient drainage slope — a common issue in Union City due to the area's moderate hurricane risk and 2-3 per year nor'easters
  • Shared-wall fire separation compliance for row house roofing

Need Flat Roof Systems in Union City?

Free estimates with no obligation.

Flat roof system costs in Union City reflect both the material specifications required for this demanding environment and the logistical premium of working in the most densely populated city in New Jersey. The combination of density-driven material upgrades and density-driven labor adds creates a cost structure that is fifteen to twenty-five percent above comparable suburban flat roof installations. A complete flat roof system replacement on a typical Union City three-story row house, including full tear-off, structural deck repair, tapered polyiso insulation, sixty-mil fully adhered TPO membrane, and parapet flashing rebuild, ranges from $14,000 to $24,000 depending on building footprint and substrate condition. Multi-building portfolio projects coordinated across adjacent row houses reduce the per-building cost by twenty to thirty percent because shared parapet work, logistics, and mobilization costs are consolidated. Commercial flat roof systems on Bergenline Avenue and Transfer Station area buildings range from $8 to $14 per square foot installed, with the per-square-foot cost varying based on equipment penetration density, required walkway pad coverage, and whether the existing deck requires structural modification for the equipment loads it supports. Larger commercial flat roofs benefit from economies of scale that smaller residential roofs do not, but the equipment-intensive rooftop configurations on Bergenline Avenue commercial buildings offset some of that savings. Modified bitumen and EPDM flat roof systems remain available at lower material cost than TPO, but we recommend TPO for most Union City applications because the reflective surface, stronger seaming, and better thermal performance in the shared-wall heat island environment provide measurably longer service life that justifies the per-square-foot premium.

What Affects Your Flat Roof Systems Cost

Roof Area

Commercial roofs are measured in squares (100 sq ft). A 10,000 sq ft warehouse roof is 100 squares — material and labor scale linearly with area.

high

Membrane System Selection

TPO and EPDM are cost-effective. PVC is premium. Modified bitumen falls in between. The choice depends on building use, energy goals, and maintenance budget.

high

Existing Roof Condition

A recover (new membrane over existing) costs 30-40% less than a full tear-off and replacement. Core sample analysis determines if recover is viable.

high

Insulation Requirements

NJ energy code requires minimum R-30 for commercial roofs. Adding tapered insulation for drainage increases both material and labor costs.

moderate

Rooftop Equipment

HVAC units, exhaust fans, satellite dishes, and other penetrations require individual flashing details that add to the scope and cost.

moderate

Access and Logistics

Urban commercial buildings with limited parking and staging area require crane lifts for material delivery, increasing mobilization costs.

moderate

A Real Flat Roof Systems Story in Union City

A Union Hill landlord who owns a row of four adjacent three-story buildings on Central Avenue approached us about a flat roof replacement strategy for his portfolio. All four buildings had aging modified bitumen flat roofs, each installed at different times over the previous twenty years, and each with at least one overlay layer. The landlord was experiencing recurring leaks in two of the four buildings and wanted a plan that addressed all four roofs in a coordinated, budget-conscious sequence.

Our inspection of the four buildings revealed varied conditions. Building One on the north end had a seventeen-year-old modified bitumen membrane with extensive alligator cracking across the south-facing two-thirds of the surface, where the lack of shade from the taller building to the north allowed maximum solar exposure. Building Two had a twelve-year-old EPDM membrane with seam failures at multiple locations, likely caused by the adhesive degradation that occurs when EPDM is installed over a previous layer without proper substrate preparation. Building Three had the newest membrane, only six years old, but it was already showing ponding issues because the installation had not addressed the deck slope that had shifted from ninety years of building settlement. Building Four on the south end had a modified bitumen membrane of unknown age with a tarred patch covering approximately thirty percent of the surface, indicating significant previous repair history.

We proposed a two-year phased flat roof replacement plan. In Year One, Buildings One and Four, the most deteriorated, would receive full tear-off to the deck with structural repair as needed, tapered polyiso insulation for positive drainage slope, and sixty-mil fully adhered white TPO membrane. The shared parapets between all four buildings would be rebuilt with our two-piece independent cap flashing system during the Year One work, because the parapet is accessible when adjacent roofs are being replaced. In Year Two, Buildings Two and Three would receive the same treatment, with the membrane tie-in to the already-installed parapet flashing on the shared walls.

The coordinated approach saved the landlord approximately thirty percent compared to four independent replacement projects because the shared parapet work was done once rather than four times, the mobilization costs were consolidated, and the DPW parking permits covered extended work windows rather than four separate applications. The tapered insulation on all four buildings eliminated the ponding problem on Building Three and created proper drainage on all four roofs, which the original flat installations had never properly addressed.

The reflective white TPO we installed reduced the rooftop surface temperatures by twenty degrees compared to the dark modified bitumen it replaced. On these Union Hill row houses where the heat island effect between shared walls drives temperatures to extremes, the reflective membrane noticeably reduced air conditioning loads for the top-floor tenants during the first summer after installation. Two full seasons later, none of the four buildings has experienced any leak, and the landlord has eliminated the annual recurring repair expense that was costing him over ten thousand dollars across the portfolio.

What Our Customers Say

After the nor'easter damaged our 1920s brownstone roof on Van Vorst Street, Jersey City Quality Roofing replaced the entire thing in four days. They handled the historic district permit and matched the slate look with architectural shingles. Outstanding crew — clean, professional, and on schedule every day.

Michael Rodriguez

Jersey City

We had a persistent leak in our Heights apartment building that three other contractors could not find. Jersey City Quality Roofing used an infrared camera and traced it to a failed pipe boot two floors away from the ceiling stain. Fixed in one afternoon. Should have called them first.

Sarah Kim

Jersey City

We hired them for a full TPO roof system on our Journal Square commercial building — about 8,000 square feet. The crew worked efficiently around our tenants, the tapered insulation eliminated the ponding problem we had for years, and the manufacturer warranty gives us peace of mind for decades.

David Okonkwo

Jersey City

A tree branch came through our roof during a summer storm in Bergen-Lafayette. They had a crew here within the hour tarping the hole and boarding it up. The permanent repair was done the following week. Only wish they had weekend scheduling for the follow-up, but the emergency response was top-notch.

Angela Martinez

Jersey City

Our Bloomfield Street brownstone had ice dam damage along the entire front eave last winter. These guys repaired the flashing, replaced the damaged shingles, and recommended ventilation improvements to prevent recurrence. Very knowledgeable about Hoboken's older buildings.

James O'Brien

Hoboken

Replacing the roof on our Washington Street row house required Historic District Commission approval. Jersey City Quality Roofing handled the entire application process and used materials that satisfied the commission while actually improving the roof performance. Five stars for navigating Hoboken's red tape.

Priya Patel

Hoboken

We were buying a third-floor condo on Park Avenue and needed a roof inspection of the building. Their report was incredibly detailed — infrared photos, moisture readings, estimated remaining life, and a maintenance plan. The seller ended up crediting us $8,000 toward the purchase based on the findings.

Thomas Walsh

Hoboken

During last March's nor'easter, our flat roof membrane blew open on Garden Street and water was pouring into our top-floor apartment. They came out at 11 PM, tarped everything, and had us dry by morning. Emergency response in Hoboken doesn't get better than this.

Maria Gonzalez

Hoboken

Our Cape Cod on Avenue C needed a complete roof replacement — the old 3-tabs were curling and missing after 25 years. They installed GAF Timberline HDZ shingles with ice-and-water shield along all the eaves and valleys. Beautiful result, and the dormers look great.

Robert Kowalski

Bayonne

Had a leak around the chimney flashing on our two-family on East 22nd Street. They replaced all the step and counter flashing and re-sealed the cricket. No more leaks through two heavy rainstorms since. Price was fair for the amount of work involved.

Josephine DeLuca

Bayonne

We had them inspect our Bergen Point rental property after a tenant complained about a ceiling stain. Turned out it was a condensation issue from inadequate attic ventilation, not a roof leak. They explained the difference clearly and recommended a fix. Saved us from an unnecessary roof repair.

Carlos Ramirez

Bayonne

Wind ripped the ridge cap off our house near Stephen Gregg Park during a storm. Water was running down both sides of the ridge into the attic. They were here in under an hour, sealed everything up that night, and did a full ridge cap replacement two days later.

Patricia Murphy

Bayonne

Our split-level on Woodcliff Avenue sits right on the Palisades ridge where the wind is brutal. They installed a wind-rated system with six nails per shingle instead of the standard four, plus extra ice shield in the valleys. First winter with zero issues after years of wind damage with the old roof.

Ahmed Hassan

North Bergen

We own a retail building on Tonnelle Avenue and needed the flat roof replaced. The modified bitumen was failing everywhere. They installed a new TPO system with proper drainage and it completely solved the ponding water problem. Great job on a large commercial project.

Lisa Chen

North Bergen

The valley on our colonial in Tyler Park was leaking into the dining room. They replaced the valley flashing and underlayment and re-shingled the affected area. Good work, though scheduling took a bit longer than expected due to their busy season.

Anthony Ferraro

North Bergen

We signed up for their commercial maintenance program for our garden apartment complex near Braddock Park. Twice a year they inspect, clean the drains, and fix small issues before they become big ones. Our emergency repair costs have dropped to nearly zero since we started.

Fatima Begum

North Bergen

Our row house on Bergenline has a flat roof that shares walls with both neighbors. These guys understood the shared-wall flashing situation perfectly — they repaired our side without disturbing the neighbor's roof. Hard to find contractors who understand Union City row house roofing.

Juan Herrera

Union City

Replacing the flat roof on our three-family walk-up in Union Hill was a challenge because of the tight street access. They managed the material delivery with a crane from the alley side and finished in three days. EPDM membrane with proper drainage — no more ponding.

Veronica Santos

Union City

They repaired the flat roof over our restaurant on Bergenline Avenue. The PVC membrane had separated at a seam near the kitchen exhaust vent. They heat-welded a patch and re-detailed the vent flashing. Solid work. Building manager was happy with the minimal disruption.

Ricardo Morales

Union City

We were considering buying a multi-family property on New York Avenue and needed a roof assessment. Their inspection revealed the flat roof had less than two years of life left — something the seller's disclosure didn't mention. That report saved us $20,000 in negotiation.

Catherine Reilly

Union City

Our apartment building on Boulevard East takes a beating from the Palisades wind. They installed a fully-adhered TPO system with extra fastening at the perimeter edges. Two winters now with zero issues. The crew knew exactly how to handle the wind exposure up here.

Diego Vargas

West New York

The parapet wall on our walk-up near Park Avenue was letting water behind the membrane. They rebuilt the parapet cap, installed new through-wall flashing, and re-terminated the membrane. Problem solved after years of patching by other contractors.

Sofia Petrov

West New York

During a December ice storm, the membrane on our flat roof split open and water poured into the top-floor apartment. They responded within two hours and got us sealed up before the next wave of freezing rain. Fast emergency work on a difficult night.

Omar Fayed

West New York

We manage several apartment buildings in West New York and enrolled them all in the maintenance program. The semi-annual inspections catch problems before our tenants notice anything. Drain cleaning alone has prevented multiple potential emergency calls.

Elena Romero

West New York

Our Harmon Cove townhouse roof was 30 years old and growing moss from all the Meadowlands humidity. They replaced it with algae-resistant architectural shingles and improved the ventilation. The HOA approved the color match and the installation was immaculate.

Kevin Brennan

Secaucus

They replaced the entire roof on our 25,000 sq ft warehouse near the Turnpike. Managed the project in phases so we never had to shut down operations. The new TPO system came with a 20-year manufacturer NDL warranty. Professional operation from start to finish.

Linda Tran

Secaucus

Had them inspect the roof on a Clarendon single-family home we were buying. Their report identified that the previous owner had layered new shingles over old ones — technically over code limit. We used that to negotiate the price down significantly.

Brian Sullivan

Secaucus

Our Millridge home had algae streaking all over the north-facing slope — a common problem near the Meadowlands. They cleaned the roof, replaced a few damaged shingles, and applied a zinc strip to prevent regrowth. Looks like a new roof.

Grace Park

Secaucus

Replaced the roof on our colonial near Gunnell Oval. The old roof was the original from when the house was built in the 1960s — way overdue. They did a clean tear-off, replaced about 15% of the decking, and installed a beautiful charcoal architectural shingle. Huge improvement.

Sean McCarthy

Kearny

Our industrial building in South Kearny near the marsh had a failing BUR roof. They installed a new EPDM system designed for the high-humidity environment with enhanced seam adhesion. No more leaks into the warehouse. The crew handled the large-scale project expertly.

Jennifer Andrade

Kearny

Ice dams damaged the eaves on our Cape Cod on Elm Street. They repaired the damaged fascia, replaced the affected shingles, and installed additional ice-and-water shield to prevent recurrence. Good work, though I wish ice dam prevention was included in the original assessment.

William Taylor

Kearny

Before listing our Passaic Avenue two-family for sale, we had them do a full roof inspection. Their report showed the roof was in good condition with 8-10 years remaining — which we included in the listing. Helped sell the property faster at asking price.

Rosa Gutierrez

Kearny

Our two-family on Harrison Avenue needed a new roof before we could refinance. They completed the replacement in three days — tear-off, decking repairs, new architectural shingles, and all new flashing. The bank appraiser was impressed with the quality.

Daniel Park

Harrison

We manage a new luxury building in the Waterfront District and had a warranty issue with the original roof contractor. Jersey City Quality Roofing came in, identified the membrane defects, documented everything for our warranty claim, and did the repair correctly.

Christine Alvarez

Harrison

Leak around the kitchen vent pipe on our older home near West Hudson Park. They replaced the pipe boot and the surrounding shingles. Quick, clean, and no more water stain spreading across the ceiling. Simple job done right.

Frank DiNapoli

Harrison

We needed a roof condition assessment for our building's reserve study near the PATH station. Their detailed report with photos and estimated replacement timeline gave our condo board exactly what we needed for long-term capital planning.

Yuki Tanaka

Harrison

Our two-family on Grant Avenue had the original roof from 1948. They navigated the tight streets with their equipment, did a careful tear-off given the shared walls with our neighbors, and installed a new roof that completely transformed the look of the house.

George Papadopoulos

East Newark

The shared-wall flashing between our row house and the neighbor's was leaking into both units. They coordinated with both homeowners, replaced the party wall flashing, and sealed everything properly. The kind of job that requires real row house experience.

Diane Wilson

East Newark

Had them inspect our small multi-family on Third Street before a planned renovation. Their report identified soft spots in the decking that we never would have found without pulling up the shingles. Changed our renovation budget significantly, but better to know now.

Joseph Medina

East Newark

A piece of the neighbor's aluminum siding flew off during a storm and punctured our flat roof membrane. Water was coming through the kitchen ceiling. They were here in 45 minutes and had the hole sealed before any serious damage to the interior.

Helen Stavros

East Newark

Our mid-rise apartment building on Park Avenue needed a complete flat roof replacement. The density in Guttenberg makes logistics a nightmare, but they managed material deliveries by crane and completed the TPO installation on schedule. Impressive project management.

Victor Petrosyan

Guttenberg

We're on the condo board for a Boulevard East building. Their maintenance program has been invaluable — the semi-annual inspections catch wind damage early before it turns into interior leaks. The annual reports help us budget for future capital improvements.

Margaret Kim

Guttenberg

Our mixed-use building had a persistent leak above the commercial space on the ground floor. They traced it to a deteriorated drain connection on the flat roof and replaced the entire drain assembly. Leak resolved. Getting equipment up to the roof in Guttenberg is always a challenge but they handled it.

Ivan Sokolov

Guttenberg

We needed a comprehensive roof assessment for all three buildings in our Galaxy Towers-adjacent complex. Their team inspected every section, mapped the moisture conditions, and gave us a prioritized 5-year replacement plan. The board voted to approve the maintenance contract on the spot.

Donna Cassidy

Guttenberg

Replacing the roof on our Victorian in the Heights was tricky — steep pitch, limited access from the narrow lot, and the wind exposure from being near the cliff edge. They handled every challenge and the new architectural shingles look amazing against the original trim.

Patrick Doyle

Weehawken

We needed emergency repair on a Lincoln Harbor commercial building where the membrane had blown up at the parapet during a windstorm. They were there the same day, secured the membrane, and scheduled the permanent repair for the following week. Responsive and competent.

Natasha Volkov

Weehawken

Our King Avenue townhouse had a leak at the skylight curb. They re-flashed the entire skylight and sealed the curb. It took longer than quoted because they found the decking around the skylight was soft, but they fixed it all and the leak is gone.

Mark Santangelo

Weehawken

Before purchasing our waterfront condo at Port Imperial, we wanted an independent assessment of the building's roof system. Their report confirmed the roof was in excellent condition with 15+ years remaining. It was exactly the peace of mind we needed for that investment.

Aisha Mohammed

Weehawken

Frequently Asked Questions About Flat Roof Systems in Union City

City of Union City Construction Department requires permits for most roofing work. Yes, a permit is required for flat roof systems projects in Union City. The municipality follows 2021 IRC/IBC as adopted by NJ DCA with wind speed requirements of 115 mph per ASCE 7-22. Additional requirements include: shared-wall fire separation compliance for row house roofing.

Request a Detailed Quote

Tell us about your project and we'll prepare a comprehensive estimate.

Your Trusted Union City Flat Roof Systems Experts

Call now for a free commercial roof assessment or request your no-obligation quote.